How can two interface communicate between them with different subnet











up vote
1
down vote

favorite












enter image description here



R1 and R2 are connected with serial cable interface but both of them having different subnet and i know they will not communicate so what are other options two communicate between them without the concept of multiple ip's










share|improve this question







New contributor




Adil Bashrahil is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
















  • 1




    Welcome to Network Engineering! For two IP hosts in different networks to communicate, you need to route between them. What you're asking to do can't be done without a lot of "magical" configuration.
    – Ron Trunk
    10 hours ago










  • I beg to differ! See answer below.
    – jonathanjo
    9 hours ago















up vote
1
down vote

favorite












enter image description here



R1 and R2 are connected with serial cable interface but both of them having different subnet and i know they will not communicate so what are other options two communicate between them without the concept of multiple ip's










share|improve this question







New contributor




Adil Bashrahil is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
















  • 1




    Welcome to Network Engineering! For two IP hosts in different networks to communicate, you need to route between them. What you're asking to do can't be done without a lot of "magical" configuration.
    – Ron Trunk
    10 hours ago










  • I beg to differ! See answer below.
    – jonathanjo
    9 hours ago













up vote
1
down vote

favorite









up vote
1
down vote

favorite











enter image description here



R1 and R2 are connected with serial cable interface but both of them having different subnet and i know they will not communicate so what are other options two communicate between them without the concept of multiple ip's










share|improve this question







New contributor




Adil Bashrahil is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.











enter image description here



R1 and R2 are connected with serial cable interface but both of them having different subnet and i know they will not communicate so what are other options two communicate between them without the concept of multiple ip's







router interface






share|improve this question







New contributor




Adil Bashrahil is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.











share|improve this question







New contributor




Adil Bashrahil is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.









share|improve this question




share|improve this question






New contributor




Adil Bashrahil is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.









asked 10 hours ago









Adil Bashrahil

61




61




New contributor




Adil Bashrahil is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.





New contributor





Adil Bashrahil is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.






Adil Bashrahil is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.








  • 1




    Welcome to Network Engineering! For two IP hosts in different networks to communicate, you need to route between them. What you're asking to do can't be done without a lot of "magical" configuration.
    – Ron Trunk
    10 hours ago










  • I beg to differ! See answer below.
    – jonathanjo
    9 hours ago














  • 1




    Welcome to Network Engineering! For two IP hosts in different networks to communicate, you need to route between them. What you're asking to do can't be done without a lot of "magical" configuration.
    – Ron Trunk
    10 hours ago










  • I beg to differ! See answer below.
    – jonathanjo
    9 hours ago








1




1




Welcome to Network Engineering! For two IP hosts in different networks to communicate, you need to route between them. What you're asking to do can't be done without a lot of "magical" configuration.
– Ron Trunk
10 hours ago




Welcome to Network Engineering! For two IP hosts in different networks to communicate, you need to route between them. What you're asking to do can't be done without a lot of "magical" configuration.
– Ron Trunk
10 hours ago












I beg to differ! See answer below.
– jonathanjo
9 hours ago




I beg to differ! See answer below.
– jonathanjo
9 hours ago










2 Answers
2






active

oldest

votes

















up vote
3
down vote













You can configure them with point-to-point routes as follows, as tested in Packet Tracer (three 2901 routers with HWIC-2T). R1 has default route to interface, R3 has default route to next-hop address, and R2 has a manual route to interface plus an interface route.



enter image description here



R1:



interface Serial0/0/0
ip address 131.43.43.1 255.255.255.224
!
ip route 0.0.0.0 0.0.0.0 Serial0/0/0


R2:



interface Serial0/0/0
ip address 131.44.44.2 255.255.255.224
clock rate 2000000
!
interface Serial0/0/1
ip address 140.10.10.2 255.255.255.224
clock rate 2000000
!
ip route 131.43.43.0 255.255.255.224 Serial0/0/0


R3:



interface Serial0/0/1
ip address 140.10.10.3 255.255.255.224
!
ip route 0.0.0.0 0.0.0.0 140.10.10.2





share|improve this answer






























    up vote
    2
    down vote













    A serial interface is (often) an "unnumbered" interface, ie. there's no need for an IP address binding (nor does one usually matter).



    Ethernet interfaces and the like require an address because Ethernet's data link layer doesn't work without a layer-2 address, and a layer-3 address is required to find out a router's local layer-2 address. A serial interface simply transmits a packet from source to destination without any need of addressing; it's always point-to-point.



    What you do need though are routing table entries for the remote subnets as jonathanjo has already pointed out. These can be set up statically or exchanged via a routing protocol like OSPF.






    share|improve this answer























      Your Answer








      StackExchange.ready(function() {
      var channelOptions = {
      tags: "".split(" "),
      id: "496"
      };
      initTagRenderer("".split(" "), "".split(" "), channelOptions);

      StackExchange.using("externalEditor", function() {
      // Have to fire editor after snippets, if snippets enabled
      if (StackExchange.settings.snippets.snippetsEnabled) {
      StackExchange.using("snippets", function() {
      createEditor();
      });
      }
      else {
      createEditor();
      }
      });

      function createEditor() {
      StackExchange.prepareEditor({
      heartbeatType: 'answer',
      convertImagesToLinks: false,
      noModals: true,
      showLowRepImageUploadWarning: true,
      reputationToPostImages: null,
      bindNavPrevention: true,
      postfix: "",
      imageUploader: {
      brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
      contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
      allowUrls: true
      },
      noCode: true, onDemand: true,
      discardSelector: ".discard-answer"
      ,immediatelyShowMarkdownHelp:true
      });


      }
      });






      Adil Bashrahil is a new contributor. Be nice, and check out our Code of Conduct.










      draft saved

      draft discarded


















      StackExchange.ready(
      function () {
      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fnetworkengineering.stackexchange.com%2fquestions%2f55093%2fhow-can-two-interface-communicate-between-them-with-different-subnet%23new-answer', 'question_page');
      }
      );

      Post as a guest















      Required, but never shown

























      2 Answers
      2






      active

      oldest

      votes








      2 Answers
      2






      active

      oldest

      votes









      active

      oldest

      votes






      active

      oldest

      votes








      up vote
      3
      down vote













      You can configure them with point-to-point routes as follows, as tested in Packet Tracer (three 2901 routers with HWIC-2T). R1 has default route to interface, R3 has default route to next-hop address, and R2 has a manual route to interface plus an interface route.



      enter image description here



      R1:



      interface Serial0/0/0
      ip address 131.43.43.1 255.255.255.224
      !
      ip route 0.0.0.0 0.0.0.0 Serial0/0/0


      R2:



      interface Serial0/0/0
      ip address 131.44.44.2 255.255.255.224
      clock rate 2000000
      !
      interface Serial0/0/1
      ip address 140.10.10.2 255.255.255.224
      clock rate 2000000
      !
      ip route 131.43.43.0 255.255.255.224 Serial0/0/0


      R3:



      interface Serial0/0/1
      ip address 140.10.10.3 255.255.255.224
      !
      ip route 0.0.0.0 0.0.0.0 140.10.10.2





      share|improve this answer



























        up vote
        3
        down vote













        You can configure them with point-to-point routes as follows, as tested in Packet Tracer (three 2901 routers with HWIC-2T). R1 has default route to interface, R3 has default route to next-hop address, and R2 has a manual route to interface plus an interface route.



        enter image description here



        R1:



        interface Serial0/0/0
        ip address 131.43.43.1 255.255.255.224
        !
        ip route 0.0.0.0 0.0.0.0 Serial0/0/0


        R2:



        interface Serial0/0/0
        ip address 131.44.44.2 255.255.255.224
        clock rate 2000000
        !
        interface Serial0/0/1
        ip address 140.10.10.2 255.255.255.224
        clock rate 2000000
        !
        ip route 131.43.43.0 255.255.255.224 Serial0/0/0


        R3:



        interface Serial0/0/1
        ip address 140.10.10.3 255.255.255.224
        !
        ip route 0.0.0.0 0.0.0.0 140.10.10.2





        share|improve this answer

























          up vote
          3
          down vote










          up vote
          3
          down vote









          You can configure them with point-to-point routes as follows, as tested in Packet Tracer (three 2901 routers with HWIC-2T). R1 has default route to interface, R3 has default route to next-hop address, and R2 has a manual route to interface plus an interface route.



          enter image description here



          R1:



          interface Serial0/0/0
          ip address 131.43.43.1 255.255.255.224
          !
          ip route 0.0.0.0 0.0.0.0 Serial0/0/0


          R2:



          interface Serial0/0/0
          ip address 131.44.44.2 255.255.255.224
          clock rate 2000000
          !
          interface Serial0/0/1
          ip address 140.10.10.2 255.255.255.224
          clock rate 2000000
          !
          ip route 131.43.43.0 255.255.255.224 Serial0/0/0


          R3:



          interface Serial0/0/1
          ip address 140.10.10.3 255.255.255.224
          !
          ip route 0.0.0.0 0.0.0.0 140.10.10.2





          share|improve this answer














          You can configure them with point-to-point routes as follows, as tested in Packet Tracer (three 2901 routers with HWIC-2T). R1 has default route to interface, R3 has default route to next-hop address, and R2 has a manual route to interface plus an interface route.



          enter image description here



          R1:



          interface Serial0/0/0
          ip address 131.43.43.1 255.255.255.224
          !
          ip route 0.0.0.0 0.0.0.0 Serial0/0/0


          R2:



          interface Serial0/0/0
          ip address 131.44.44.2 255.255.255.224
          clock rate 2000000
          !
          interface Serial0/0/1
          ip address 140.10.10.2 255.255.255.224
          clock rate 2000000
          !
          ip route 131.43.43.0 255.255.255.224 Serial0/0/0


          R3:



          interface Serial0/0/1
          ip address 140.10.10.3 255.255.255.224
          !
          ip route 0.0.0.0 0.0.0.0 140.10.10.2






          share|improve this answer














          share|improve this answer



          share|improve this answer








          edited 4 hours ago

























          answered 9 hours ago









          jonathanjo

          8,9511630




          8,9511630






















              up vote
              2
              down vote













              A serial interface is (often) an "unnumbered" interface, ie. there's no need for an IP address binding (nor does one usually matter).



              Ethernet interfaces and the like require an address because Ethernet's data link layer doesn't work without a layer-2 address, and a layer-3 address is required to find out a router's local layer-2 address. A serial interface simply transmits a packet from source to destination without any need of addressing; it's always point-to-point.



              What you do need though are routing table entries for the remote subnets as jonathanjo has already pointed out. These can be set up statically or exchanged via a routing protocol like OSPF.






              share|improve this answer



























                up vote
                2
                down vote













                A serial interface is (often) an "unnumbered" interface, ie. there's no need for an IP address binding (nor does one usually matter).



                Ethernet interfaces and the like require an address because Ethernet's data link layer doesn't work without a layer-2 address, and a layer-3 address is required to find out a router's local layer-2 address. A serial interface simply transmits a packet from source to destination without any need of addressing; it's always point-to-point.



                What you do need though are routing table entries for the remote subnets as jonathanjo has already pointed out. These can be set up statically or exchanged via a routing protocol like OSPF.






                share|improve this answer

























                  up vote
                  2
                  down vote










                  up vote
                  2
                  down vote









                  A serial interface is (often) an "unnumbered" interface, ie. there's no need for an IP address binding (nor does one usually matter).



                  Ethernet interfaces and the like require an address because Ethernet's data link layer doesn't work without a layer-2 address, and a layer-3 address is required to find out a router's local layer-2 address. A serial interface simply transmits a packet from source to destination without any need of addressing; it's always point-to-point.



                  What you do need though are routing table entries for the remote subnets as jonathanjo has already pointed out. These can be set up statically or exchanged via a routing protocol like OSPF.






                  share|improve this answer














                  A serial interface is (often) an "unnumbered" interface, ie. there's no need for an IP address binding (nor does one usually matter).



                  Ethernet interfaces and the like require an address because Ethernet's data link layer doesn't work without a layer-2 address, and a layer-3 address is required to find out a router's local layer-2 address. A serial interface simply transmits a packet from source to destination without any need of addressing; it's always point-to-point.



                  What you do need though are routing table entries for the remote subnets as jonathanjo has already pointed out. These can be set up statically or exchanged via a routing protocol like OSPF.







                  share|improve this answer














                  share|improve this answer



                  share|improve this answer








                  edited 7 hours ago

























                  answered 9 hours ago









                  Zac67

                  24.3k21252




                  24.3k21252






















                      Adil Bashrahil is a new contributor. Be nice, and check out our Code of Conduct.










                      draft saved

                      draft discarded


















                      Adil Bashrahil is a new contributor. Be nice, and check out our Code of Conduct.













                      Adil Bashrahil is a new contributor. Be nice, and check out our Code of Conduct.












                      Adil Bashrahil is a new contributor. Be nice, and check out our Code of Conduct.
















                      Thanks for contributing an answer to Network Engineering Stack Exchange!


                      • Please be sure to answer the question. Provide details and share your research!

                      But avoid



                      • Asking for help, clarification, or responding to other answers.

                      • Making statements based on opinion; back them up with references or personal experience.


                      To learn more, see our tips on writing great answers.





                      Some of your past answers have not been well-received, and you're in danger of being blocked from answering.


                      Please pay close attention to the following guidance:


                      • Please be sure to answer the question. Provide details and share your research!

                      But avoid



                      • Asking for help, clarification, or responding to other answers.

                      • Making statements based on opinion; back them up with references or personal experience.


                      To learn more, see our tips on writing great answers.




                      draft saved


                      draft discarded














                      StackExchange.ready(
                      function () {
                      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fnetworkengineering.stackexchange.com%2fquestions%2f55093%2fhow-can-two-interface-communicate-between-them-with-different-subnet%23new-answer', 'question_page');
                      }
                      );

                      Post as a guest















                      Required, but never shown





















































                      Required, but never shown














                      Required, but never shown












                      Required, but never shown







                      Required, but never shown

































                      Required, but never shown














                      Required, but never shown












                      Required, but never shown







                      Required, but never shown







                      Popular posts from this blog

                      A CLEAN and SIMPLE way to add appendices to Table of Contents and bookmarks

                      Calculate evaluation metrics using cross_val_predict sklearn

                      Insert data from modal to MySQL (multiple modal on website)